|
|
Полученную смесь можно использовать в течение 2-х часов при температуре +20 град. С. Нанесение: Штукатурный раствор наносят на поверхность в один слой и разравнивают. Оптимальная толщина слоя - 10 мм (минимальная - 8 мм).
|
|
|
For any types of surface - concrete, stone, brick, wood. characteristic: represents the âûñîêîàäãåçèîííóþ plaster on the basis of gypsum astringent and nonorganic microfillers. Gypsum plaster the solution makes it possible to receive absolutely the smooth surface, which not need additional filling before further works and has the short period of drying. surface preparation: the surface should be dry and hard, dust-free , butters and other pollutions of organically derived. Strongly absorbing surface one should to process prime coating of ANKER-ïðàéìåð. plaster preparing: dry plaster mixture is combined with pure water to homogeneous state in ratio of 7, 5-8, 5 l by 15 kg of dry mixture. The solution is being held 5 mine, then again are mixed. After that the mixture is ready for work. Received the mixture can be used in two hours at a temperature of +20 degree. S. coating: the mortar for plastering inflict at the surface the single-skin and ðàçðàâíèâàþò. | optimal layer thickness - 10 MM (minimum - 8 MM). Through 45-60 minutes after solution coating (initial set) the surface process by the wide spatula, and hereinafter through 15-20 minutes overwrite spongy grater, abundantly moistened with water and çàãëàæèâàþò metal spatula, receiving absolutely smooth surface. expenditure: the expenditure of dry plaster mixture makes up 8-9 the kg by 1 sq. m in case of layer coating 10 MM. storage: the sacks with gypsum plaster mixture keep in dry place on wood blanket. Storage life not more 6 months. technical data: mixture proportion: by 1 kg - 0, 52-0, 55 waters l; by 1 sack (15 kg) - 7, 5-8, 5 waters l; ground temperature: from + 50 hails to + 30 ãðàäÑ; fitness time of solution: 1 ch; layer thickness: 10 MM. the product was admitted to use the solar power station,. Moscow.
|
|
|
For any types of surface - concrete, stone, brick, wood. characteristic: represents the âûñîêîàäãåçèîííóþ plaster on the basis of gypsum astringent and nonorganic microfillers. Gypsum plaster the solution makes it possible to receive absolutely the smooth surface, which not need additional filling before further works and has the short period of drying. surface preparation: the surface should be dry and hard, dust-free , butters and other pollutions of organically derived. Strongly absorbing surface one should to process prime coating of ANKER-ïðàéìåð. plaster preparing: dry plaster mixture is combined with pure water to homogeneous state in ratio of 7, 5-8, 5 l by 15 kg of dry mixture. The solution is being held 5 mine, then again are mixed. After that the mixture is ready for work. Received the mixture can be used in two hours at a temperature of +20 degree. S. coating: the mortar for plastering inflict at the surface the single-skin and ðàçðàâíèâàþò. | optimal layer thickness - 10 MM (minimum - 8 MM). Through 45-60 minutes after solution coating (initial set) the surface process by the wide spatula, and hereinafter through 15-20 minutes overwrite spongy grater, abundantly moistened with water and çàãëàæèâàþò metal spatula, receiving absolutely smooth surface. expenditure: the expenditure of dry plaster mixture makes up 8-9 the kg by 1 sq. m in case of layer coating 10 MM. storage: the sacks with gypsum plaster mixture keep in dry place on wood blanket. Storage life not more 6 months. technical data: mixture proportion: by 1 kg - 0, 52-0, 55 waters l; by 1 sack (15 kg) - 7, 5-8, 5 waters l; ground temperature: from + 50 hails to + 30 ãðàäÑ; fitness time of solution: 1 ch; layer thickness: 10 MM. the product was admitted to use the solar power station,. Moscow.
|
|
|
For any types of surface - concrete, stone, brick, wood. characteristic: represents the âûñîêîàäãåçèîííóþ plaster on the basis of gypsum astringent and nonorganic microfillers. Gypsum plaster the solution makes it possible to receive absolutely the smooth surface, which not need additional filling before further works and has the short period of drying. surface preparation: the surface should be dry and hard, dust-free , butters and other pollutions of organically derived. Strongly absorbing surface one should to process prime coating of ANKER-ïðàéìåð. plaster preparing: dry plaster mixture is combined with pure water to homogeneous state in ratio of 7, 5-8, 5 l by 15 kg of dry mixture. The solution is being held 5 mine, then again are mixed. After that the mixture is ready for work. Received the mixture can be used in two hours at a temperature of +20 degree. S. coating: the mortar for plastering inflict at the surface the single-skin and ðàçðàâíèâàþò. | optimal layer thickness - 10 MM (minimum - 8 MM). Through 45-60 minutes after solution coating (initial set) the surface process by the wide spatula, and hereinafter through 15-20 minutes overwrite spongy grater, abundantly moistened with water and çàãëàæèâàþò metal spatula, receiving absolutely smooth surface. expenditure: the expenditure of dry plaster mixture makes up 8-9 the kg by 1 sq. m in case of layer coating 10 MM. storage: the sacks with gypsum plaster mixture keep in dry place on wood blanket. Storage life not more 6 months. technical data: mixture proportion: by 1 kg - 0, 52-0, 55 waters l; by 1 sack (15 kg) - 7, 5-8, 5 waters l; ground temperature: from + 50 hails to + 30 ãðàäÑ; fitness time of solution: 1 ch; layer thickness: 10 MM. the product was admitted to use the solar power station,. Moscow.
|
|
|
For any types of surface - concrete, stone, brick, wood. characteristic: represents the âûñîêîàäãåçèîííóþ plaster on the basis of gypsum astringent and nonorganic microfillers. Gypsum plaster the solution makes it possible to receive absolutely the smooth surface, which not need additional filling before further works and has the short period of drying. surface preparation: the surface should be dry and hard, dust-free , butters and other pollutions of organically derived. Strongly absorbing surface one should to process prime coating of ANKER-ïðàéìåð. plaster preparing: dry plaster mixture is combined with pure water to homogeneous state in ratio of 7, 5-8, 5 l by 15 kg of dry mixture. The solution is being held 5 mine, then again are mixed. After that the mixture is ready for work. Received the mixture can be used in two hours at a temperature of +20 degree. S. coating: the mortar for plastering inflict at the surface the single-skin and ðàçðàâíèâàþò. | optimal layer thickness - 10 MM (minimum - 8 MM). Through 45-60 minutes after solution coating (initial set) the surface process by the wide spatula, and hereinafter through 15-20 minutes overwrite spongy grater, abundantly moistened with water and çàãëàæèâàþò metal spatula, receiving absolutely smooth surface. expenditure: the expenditure of dry plaster mixture makes up 8-9 the kg by 1 sq. m in case of layer coating 10 MM. storage: the sacks with gypsum plaster mixture keep in dry place on wood blanket. Storage life not more 6 months. technical data: mixture proportion: by 1 kg - 0, 52-0, 55 waters l; by 1 sack (15 kg) - 7, 5-8, 5 waters l; ground temperature: from + 50 hails to + 30 ãðàäÑ; fitness time of solution: 1 ch; layer thickness: 10 MM. the product was admitted to use the solar power station,. Moscow.
|
